Rukus Wireless ZoneFlex 7731 Guía de usuario Pagina 61
- Pagina / 120
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
53
Configuring the Access Point
Configuring Internet Settings
PPPoE
Point to Point Protocol over Ethernet (PPPoE) is a Layer 2 protocol which uses the PPP
(Point to Point) protocol to connect a client system to a server system over a one to
one network link. All traffic for a PPPoE connected client must go through the PPPoE
server to reach the client. A PPPoE server can therefore be used to route, NAT, firewall,
and perform QoS traffic shaping.
If a PPPoE server is used to distribute Internet access to subscribers, the Access Point
can be configured with a PPPoE username and password to authenticate with the
PPPoE server.
PPPoE is available only for the IPv4 connection type; PPPoE is not supported in IPv6
environments.
To set the IPv4 connection type to PPPoE
1. Go to Configuration > Internet.
2. Under IPv4 Connection Type, select PPPoE.
3. Enter an IPv4 Primary DNS Server address. Secondary DNS server is optional.
4. Enter a PPPoE Username.
5. Enter a PPPoE Password.
6. Retype the password in PPPoE Password Confirmation.
7. Click Update Settings to save your changes.
Configuring L2TP Connection Settings
You can implement transparent bridging with ZoneFlex through the use of L2TP (Layer
2 Tunneling Protocol) tunneling. By tunneling traffic from a ZoneFlex AP to a central-
ized data center, access controllers with policy enforcement software can apply rules
and services. In a typical WLAN implementation, these rules include a captive portal
to authenticate users’ credentials.
In the case of L2TP, the ZoneFlex AP functions as a remote bridge. As such, it forwards
traffic into PPP sessions over the L2TP tunnel. This implementation ensures that you
have complete visibility into MAC addresses of users, as individual Wi-Fi clients are
essentially placed (bridged) onto the ISP’s core network.
- Ruckus Wireless 1
- ZoneFlex 1
- Indoor Access Point 1
- Release 9.3 User Guide 1
- Contents 3
- About This Guide 7
- Related Documentation 8
- Documentation Feedback 8
- Package Contents 10
- Side Panel Features 11
- Rear Panel Features 13
- ZoneFlex 7962 Access Point 15
- ZoneFlex 7341 Access Point 19
- ZoneFlex 7343 Access Point 21
- Rear Panel 24
- ZoneFlex 7363 Access Point 25
- Installing the Access Point 29
- Perform a Site Survey 30
- Orientation 31
- Before You Begin 32
- What You Will Need 36
- ZoneDirector 37
- Management by FlexMaster 38
- Computer 39
- Configure Wireless # Settings 42
- Settings 44
- Check the LEDs 46
- Troubleshooting Installation 49
- Navigating the Web Interface 51
- Configuring the Access Point 55
- Configuring Device Settings 56
- Configuring Internet Settings 57
- NTP Server 58
- Management VLAN 58
- DHCP / Auto Configuration 59
- Static IP 60
- Configuring Local Subnets 63
- Configuring Wireless Settings 64
- Using WEP 72
- Using WPA 74
- Customizing 802.1X Settings 77
- Setting Threshold Options 78
- Rate Limiting 80
- Access Control Options 81
- Removing a MAC Address 82
- Configuring Ethernet Ports 83
- Setting Ethernet Port Type 85
- General Port 86
- Configuring Hotspot Service 88
- Managing the Access Point 100
- Pointing the AP to FlexMaster 107
- Syslog Server 108
- Upgrading the Firmware 110
- Scheduling Automatic Upgrades 111
- Rebooting the Access Point 112
- Defaults 113
- Running Diagnostics 114
- Figure 54. Pinging a client 115
Samsung GT-S7250 manuali
Manuali dei proprietari e guide per l'utente per Telefonini Samsung GT-S7250.
We fornisce 4 manuali pdf Samsung GT-S7250 per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Comentarios a estos manuales